|
CCNABRAINDUMP4(1) |
| 来源:www.stu88.com 时间:2006-04-01 |
|
I took the CCNA exam yesterday, it was really tough but Al-hamdulellah (thanks God) I passed from the first time with 81% and the certificate's result was :
Advanced Cisco Router Configuration 100%.
Cisco LAN Switch Configuration 61%.
I thought my background of MCSE was enough to take the advantage to eat the OSI model questions, so I did’nt read it well enough, don't do it Mr./Ms. MCSE, and you who is Mr./Ms. None MCSE work hard on it and on the Subnetting, you can guarantee 25-30 % of the entire percentage if you are good enough in both of them...
The bugs that was reported in the pool questions earlier for CCNA Exams have been fixed, but not for the CMTD Exam's pool yet !!
My advice to you is to read ICRC book (or whatever ) once very quickly in 2-3 days for example regardless of understanding everything in those 2 days 100%, just to build a quick and general idea about the entire CCNA course and then either trying to answer yourself the CISCO’s CCNA 60 exam objectives that on CISCO site www.cisco.com and compare your answers with Diamond's braindump, or try to get any good test program (for example BOSON one that on www.boson.com it's good for this stage), after either of them or even both, read your reference book again but in detail word by word and try to answer every preview question after every chapter (this may take a little longer time)..
If you don't have time for the second real reading of your reference book, then enough with any good test program like BOSON and the following Questions with their answers, you will get for sure more than 75% in one condition, PAY ALL YOUR ATTENTION in reading every question in your real CCNA exam very carefully, and take your time in it, a lot of the questions you will find the answer between the lines, and some OSI models questions gives the right answers for the other OSI models questions, so in the exam mark all the OSI model questions to compare them with each other.
The question that have ‘@’ symbol means it came almost exactly, and the question that with ‘§’ symbol means it was in my real Exam in the same concept but in other words ..
1. Which command will display the settings of the routers ARP cache learned through the Ethernet interface?
Show interface ethernet 0 arp
Show arp interface ethernet 0
Show arp
Show ip arp
(Check this question, I doubt “ Show ip arp “ )
2. Which of the following commands can be run from user level?
Show aliases
Show arp
Show users
Show ppp
Show interface serial 0
Show version
Show running-config
3. How would you set the 3rd port, on the supervisor module installed in slot 1 on a Cisco 5000 to high priority?
Set port level 1/3 high
Set port level 0/2 high
Set 1/3 level high
Set 0/2 level high
There is no such available setting in the Cisco Switching IOS
4. How many classes of addresses are available for use on the internet?
1
2
3
4
5
5. Identify the correct classifications of address classes: (2)
A – uses two octets to make up the netmask
B – uses three octets to make up the netmask
C – uses a netmask prefix of 26
D – used for broadcasting
E – used for testing
6. § type the command to instruct the router to load the IOS from Read Only Memory?
Load system rom
boot system rom.
run rom
boot system default
7. Identify the statement which would permit only smtp mail to access the host 209.76.25.1
A. Access-list 101 deny ip any any
Access-list 101 permit tcp any 209.76.25.1 eq smtp
B. Access-list 101 permit tcp any 209.76.25.1 eq smtp
Access-list 101 deny ip any 209.76.25.1 共7页: 1 [2] [3] [4] [5] [6] [7] 
下一篇：CCNABRAINDUMP6
| |
| [编辑：煮酒论剑] [打印本页] [返回顶部↑] |
|
|
|
|
|
|
|
